Magnetic Separation for Kaolin and Mineral Processing
Wet high-intensity separation for weakly magnetic iron- and titanium-bearing minerals where brightness, whiteness and grade define acceptance.

Visão geral
Kaolin brightness and grade are limited by iron- and titanium-bearing minerals that arrive with the ore and survive conventional processing. Much of that contamination is only weakly magnetic, so a standard grate or drum will pass it. Removing it requires a high-intensity field applied to a dispersed slurry, which is why kaolin brightening is a wet high-intensity duty rather than a tramp-metal duty. The same principle applies across mineral processing — feldspar, silica sand, calcium carbonate and ceramic raw materials all face a similar weakly magnetic fraction. A wet high intensity magnetic separator is the equipment this duty requires.This page covers what limits brightness, why intensity matters, how the circuit is arranged, and what to specify.

A coarse stage protects the high-intensity matrix
Kaolin, feldspar, silica and ceramic raw materials require a circuit built around mineralogy, dispersion, residence time and matrix cleaning.
What Limits Kaolin Brightness and Grade
Brightness is a measure of how much light the powder reflects, and iron-bearing minerals absorb light rather than reflect it. Even a small fraction changes the measured value, which is why brightness specifications are tight and why contamination that would be invisible in a bulk chemical matters here.
The minerals responsible fall into two groups. Discrete iron oxide and hydroxide particles — hematite and goethite among them — are the more straightforward case, because they are separate particles that can be captured if the field is strong enough. Titanium-bearing minerals such as anatase, rutile and ilmenite are the harder case: some occur as liberated particles, but some are associated with the clay structure itself, where no mechanical separation can reach them.
That distinction sets the realistic expectation for magnetic separation. It removes liberated magnetic and weakly magnetic particles effectively. It does not remove iron or titanium that is structurally part of the clay particle. A circuit that is expected to solve both will under-deliver, and the shortfall is usually attributed to the equipment rather than to the mineralogy.
Particle size adds a second constraint. Kaolin is processed fine, and the fines carry a disproportionate share of the contaminating minerals. A separator that works on the coarse fraction will report good recovery while the product brightness stays flat.
Why Weakly Magnetic Minerals Need High-Intensity Separation
Field strength alone is not the variable that matters. Capture depends on the field gradient at the matrix surface, the residence time in the field, and the magnetic susceptibility of the particle.
Iron-bearing minerals in kaolin have low susceptibility compared with ferrous metal. A standard ferrite or neodymium element produces a gradient that is adequate for tramp metal and inadequate for these minerals. The particle passes through the field without being captured, and the test reports the expected removal of coarse iron with no change in brightness.
High-intensity electromagnetic separation addresses this by combining a strong background field with a matrix that concentrates the gradient. The trade-off is that the matrix is fragile in the wrong hands: it blinds if coarse material reaches it, and it needs a flush cycle to release what it has captured. Both of these shape the circuit design rather than being operating details.
The practical consequence is that a high-intensity stage is always preceded by a coarse stage. Placing the high-intensity element directly after the blunger or screen means it spends its capacity on material the coarse stage should have removed.
The Wet High-Intensity Circuit in Practice
Kaolin is treated as a dispersed slurry, so the circuit is built around slurry handling rather than around a single unit.
Dispersion and screening. The clay is blunged and screened to remove coarse material and oversize. This protects the matrix downstream and stabilises the feed.
Coarse magnetic removal. A drum or grate stage removes the ferrous fraction that would otherwise blind the high-intensity matrix. This stage is cheap and protects an expensive one.
High-intensity separation. The slurry passes through the matrix in the background field. Residence time, solids loading and field setting determine recovery. A wet type electromagnetic separator is the unit used at this position, sized on slurry flow rather than on dry throughput.
Flush and matrix cleaning. Captured material is released on a cycle. If the flush is incomplete, the matrix progressively blinds and recovery falls without any change in the field reading.
Dewatering and product handling. Downstream of separation, the slurry is dewatered and dried. Contamination introduced here — from unlined equipment or from wear — is not recoverable by the separator upstream.
For coarser mineral streams where the magnetic fraction is more strongly responsive, a drum type magnetic separator covers the duty at higher throughput and lower intensity. The choice between drum and high-intensity matrix follows the susceptibility of the target mineral, not the tonnage.
Wet High Intensity Magnetic Separator Equipment for Kaolin
Kaolin circuits combine a coarse protection stage with a high-intensity stage, and the units below cover both positions. Each links to the product page with its field rating and construction details; the working figure is confirmed against the actual feed at quotation stage.
| Equipamento | Field | Position it serves |
|---|---|---|
| Wet type electromagnetic separator | 23,000 Gs | High-intensity stage on dispersed kaolin slurry |
| Vertical ring high gradient separator | High-gradient, oil-water cooled | Continuous high-intensity duty at larger throughput |
| Drum magnetic separator | 8,000 Gs | Coarse ferrous removal ahead of the high-intensity stage |
| Separador magnético de meio tambor | Up to 6,000 Gs | Dry bulk and powder streams |
| Magnetic pulley separator | 15,000 Gs | Conveyor head pulley, continuous tramp removal |
| Cross belt magnets | Permanente | Overhead conveyor duty with self-cleaning |
| Self-cleaning hump magnet | 12.000 Gs | Abrasive bulk material in gravity chutes |
| Conveyor belt magnetic separator | 15,000 Gs dual-stage | Conveyor lines requiring two-stage removal |
| Magnetic bar and tube separator | 14.000 Gs | Pipe transfer and silo outlets |
The pairing is the design decision, not the individual unit. A high-intensity matrix is the most expensive element in the circuit and the easiest to damage, so the coarse stage ahead of it is what determines whether the high-intensity stage survives its first month. Where the feed varies with the ore body, sizing the coarse stage for the worst case rather than the average is the cheaper choice over a season.
Selection Inputs for Kaolin
Kaolin circuits are specified on slurry behaviour and mineralogy, not on tonnage alone.
- Target brightness and grade — the specification that has to be met, expressed in the same units the lab reports.
- Mineralogy of the contaminant — which iron and titanium minerals are present, and how much is liberated rather than associated with the clay.
- Feed particle size distribution — the fines fraction usually carries the contamination.
- Solids loading — sets viscosity and therefore residence time in the matrix.
- Slurry flow rate — the sizing basis for a wet high-intensity unit.
- pH and dispersion state — affects whether particles report as discrete entities or as flocs.
- Flush water availability and quality — the flush cycle is part of the process, not an afterthought.
- Matrix and housing material — abrasion from the slurry determines wear life.
The most common specification error is quoting a unit on dry tonnage. A wet circuit is sized on slurry volume and residence time, and two plants with the same tonnage but different solids loading need different equipment.
How It Compares With Chemical Bleaching
Magnetic separation and chemical bleaching are usually presented as alternatives. In practice they address different fractions, and most brightening circuits use both.
| Separação magnética | Reductive bleaching | |
|---|---|---|
| Target | Liberated magnetic and weakly magnetic particles | Dissolved and surface iron |
| Mechanism | Physical capture in a field | Chemical reduction to a soluble form |
| Effect on titanium minerals | Removes liberated titanium-bearing particles | Limitado |
| Reagent and effluent | Nenhum | Reducing agent and effluent handling |
| Operating cost profile | Mainly power and maintenance | Mainly reagents |
| Position in the circuit | Before bleaching, to reduce the load | After separation |
The ordering matters. Removing the liberated magnetic fraction first reduces the reagent demand of the bleaching step and reduces the solids that would otherwise consume reagent. A circuit that bleaches without prior magnetic removal carries a reagent cost that the separation step would have avoided.
For ceramic raw materials where the contamination profile is similar, the approach and the quality measures are set out in enhancing ceramic purity.
Quality Control and Verification
Brightness is measured on the product, but it is a lagging indicator — by the time it moves, the circuit has been off for a while. Two leading indicators are more useful.
The first is the field and matrix condition. Field measurement on each element against the unit serial number confirms the unit is as specified; the flush cycle record confirms the matrix is being cleaned. Together they explain most of the drift that appears as a brightness change.
The second is a periodic spiked-slurry test at the operating velocity. This gives a recovery figure for the actual feed, which is the only number that predicts performance when the ore body changes. The method is described in the processo de ensaio de separador magnético.
When the ore source changes, re-run the test rather than adjusting the field setting by feel. A change in mineralogy alters which fraction is responsive, and the correct response is often a change in residence time rather than in intensity.
To have a kaolin or mineral circuit reviewed against a specific feed and brightness target, send the material data through the customisation enquiry.
Related Material Guides
Mineral processing covers a range of feeds with different mineralogy, and the technical detail differs enough between them that each gets its own treatment. The guides below cover what has been published, and this section is where new material-specific articles are added as they are written.
Ceramic raw materials. Feldspar, silica and ceramic body materials face a contamination profile close to kaolin, with brightness and whiteness specifications driving the same high-intensity requirement. The approach and the quality measures are set out in enhancing ceramic purity.
Sizing and material data. What to send for a slurry or powder stream, and how a circuit is assessed against a brightness or grade target, is covered in magnetic separation sizing and analysis.
Metal recovery from mineral streams. Where the objective is recovering rather than removing the magnetic fraction, a set of worked cases is documented in metal recovery with magnetic separators.
Bauxite, quartz and heavy mineral sands are not yet written up as separate guides. Where a feed is not covered, the sizing route above is the starting point, because the mineralogy of the contaminant rather than the material name is what determines whether a magnetic stage will work at all.
Perguntas mais frequentes
Can magnetic separation replace chemical bleaching entirely?
Why does the brightness not improve after installing a separator?
Does a stronger field always give better recovery?
How is performance verified on a production circuit?
Match the field, housing and cleaning method to the actual stream.
Send the material form, particle size, throughput, temperature, line pressure and target contamination level for a configuration review.
Start your project →