electromagnetic separator dry type
Electromagnetic Separator (Dry Type)
Industrial Wet-Type Electromagnetic Separator for Battery Slurry Purification
Electromagnetic Separator (Wet Type)
eddy currrent separator
Eccentric Eddy Current Separator & Stainless Steel Separator Combination
Self Cleaning Electro Magnet
Automatic Powder Magnetic Filter
Converyor Belt Magnetic Separator
Automatic Magnetic Liquid Trap
Automatic Rotary Grate Magnetic Separator
Automatic Rotary Grate Magnetic Separator
Chemical processing

Magnetic Separation for Chemical Processing

A pipeline magnetic separator remove ferrous wear and tramp-metal from chemical powders, slurries and aggressive liquids where ferrous contamination affects yield or batch acceptance.

Powders Slurries Liquids CIP/SIP
Review equipment options
Automatic powder magnetic separator installed below a chemical reactor discharge hopper
Application image supplied for this industry page.
316L Wetted surfaces
23,000 Gs High-intensity option
ATEX Zone 22 option

Overview

Ferrous contamination enters a chemical process from raw materials, from wear on mills, pumps and valves, and from packaging and handling. Removing it depends less on magnet strength than on matching the separator to the material form — powder, slurry or liquid — and to the cleaning regime the plant can actually sustain.

A separator that cannot be cleaned on schedule loses effectiveness within days, whatever its rated field. This page sets out where contamination enters, which separator type fits each stream, the inputs that change the specification, and how removal is verified before a unit is released.

Automatic self-cleaning Pipeline magnetic separator for bridging chemical materials with rotary grate
Application view

Designed around the real material stream

Pipeline, grate and filter separators for chemical powders, slurries and aggressive liquids. Separator selection is driven by flow behaviour, contamination size, access and the cleaning routine the plant can sustain.

Where Ferrous Contamination Enters a Chemical Process

Raw materials carry the largest share in most audits. Mineral fillers, pigments, catalyst precursors and recycled feedstock all arrive with trace iron that was present in the ore or introduced during grinding and sieving.

Because these materials are bought to a specification rather than a contamination limit, the iron arrives as a normal part of the supply, not as an exception.

Equipment wear adds a second stream. Mills, crushers, screw conveyors, pumps and valve seats shed ferrous particles continuously, and the rate rises with abrasive or corrosive duty.

Handling and storage contribute a third. Carbon-steel drums, unlined chutes, rust from condensate and swarf from maintenance work can all enter the process.

Particle size decides how difficult the problem is to solve. Particles above roughly 100 µm are captured reliably by most magnetic elements. Particles below about 50 µm require a higher field gradient and a slower approach velocity.

Choosing Between Pipeline, Grate, Drawer and Filter Separators

The equipment follows the material form and the position in the line where access is possible. There is no single separator type that covers powders, slurries and liquids at once.

Separator type Best suited to Typical position Main limitation
Pipeline magnetic trap Liquids, semi-liquids and closed transfer lines Before pumps, reactors and filling heads Needs a maintenance window for rod cleaning
Grate and drawer magnets Free-flowing powders, granules and pellets Chutes, hoppers, bag dumps and gravity lines Bridging risk with fine or damp powders
Rotary magnetic separator Continuous powder flow with automatic discharge Pneumatic or gravity powder transfer Higher mechanical complexity
High-gradient powder filter Fine powders needing a stronger field Before packing or reaction Higher pressure drop
Wet electromagnetic separator Fine weakly magnetic particles in slurry Slurry lines and recirculation loops Requires slurry handling and flush water

For liquid lines, an automatic pipeline liquid trap is usually the first unit considered.

For powder lines, an automatic powder magnetic filter covers duties where the field requirement is higher than a static grate can deliver.

Where the line carries bulk powder with intermittent cleaning, an automatic rotary magnetic separator removes the manual cleaning step that can otherwise be skipped.

Equipment for Chemical Processing Duty

The positions described above map to a set of standard units rather than bespoke designs. Each entry links to the product page where the field rating, housing material and connection details are listed.

Equipment Field Position it serves
Magnetic grate separator 12,000 Gs Powder and granule chutes, hoppers and bag-dump stations
Magnetic drawer separator High intensity Powder lines requiring tool-free pull-out cleaning
Automatic rotary magnetic separator 14,000 Gs Cohesive or bridging powders
Automatic powder magnetic filter 9,000–14,000 Gs High-capacity powder duty before packing or reaction
Positive-pressure powder filter 14,000 Gs Fine powder with continuous online cleaning
Magnetic liquid trap Up to 14,000 Gs High-pressure and high-temperature liquid lines
Automatic magnetic liquid trap 10,000 Gs Semi-liquids and viscous products
Magnetic strainer 13,000 Gs Solvents, coatings and process fluids
Insulated separator for hot viscous liquids Heat-retaining jacket Hot viscous duty where the product must not solidify
Dry electromagnetic separator 23,000 Gs Ultra-fine ferrous removal from powders
Wet electromagnetic separator 23,000 Gs Fine weakly magnetic particles in slurry

Start with the position carrying the highest contamination load, which is usually the raw-material intake, rather than the position that is easiest to reach.

Where a high-intensity stage is used, put a coarse stage ahead of it. A high-gradient element fed with tramp metal can become overloaded within days.

Selection Inputs That Change the Equipment

A quotation built on flow rate alone will usually be wrong. The following inputs change the housing, magnetic element and cleaning method.

  • Material form — powder, granule, slurry, paste or liquid.
  • Particle size — the fine fraction sets the field-gradient requirement.
  • Bulk density — determines whether the material will bridge.
  • Flow rate and line size — set the approach velocity.
  • Viscosity and solids loading — determine residence time and flushing.
  • Temperature and pressure — constrain magnet grade, housing and seals.
  • Cleaning frequency — determines manual or automatic cleaning.
  • Classification — includes CIP/SIP and ATEX requirements.
  • Construction material — 304, 316L, finish and gasket compatibility.

The most frequent specification error is sizing a unit on nominal flow rather than the velocity at the magnetic surface. Two lines with the same flow rate but different diameters can produce very different capture performance.

Materials, Pressure Rating and Cleaning Regime

Wetted parts in chemical duty are normally 304 or 316L stainless steel. The choice follows the process fluid rather than a default. Chlorides, acids and some solvents make 316L the practical minimum, while neutral aqueous duty can often use 304.

Gasket material must be selected against the same process fluid. A correctly rated housing with an incompatible seal will fail at the seal rather than at the housing.

Surface finish matters where material adheres. A rough internal surface retains product and can become a contamination source between batches.

Where the plant runs a validated cleaning cycle, the separator must be compatible with that cycle rather than requiring a separate cleaning process.

For dust atmospheres, ATEX zoning determines whether a standard motor and housing can be used or whether an explosion-protected configuration is required.

Configurations by Chemical Segment

Chemical-processing duties differ enough between segments that one configuration rarely covers every application.

Pigments, dyes and carbon black. Colour and dispersion quality are sensitive to fine iron. The material is often handled as a fine powder with a tendency to aerate, making high-gradient powder filtration before packing a common position.

A worked example is available in the carbon black separation case study .

Catalysts and catalyst precursors. Iron affects selectivity and can poison the active phase. Contamination control normally sits early in the process, on the precursor solution or slurry.

Mineral fillers. Calcium carbonate, talc and kaolin carry iron-bearing minerals from the ore. Brightness and whiteness specifications make this a high-intensity duty rather than a simple tramp-metal duty.

Coatings, resins and solvents. Pipeline traps ahead of filters and filling heads protect both the product and downstream filter media.

Agrochemicals. Quick-release magnetic elements reduce changeover time between formulations.

For a broader technical treatment, see magnetic separator for chemical industry .

Verifying Performance Before and After Installation

A separator is only as good as the verification behind it. Two checks matter in practice.

The first is field verification on the magnetic element. Measuring the field at a defined position on each rod and recording the result against the unit serial number provides an auditable record.

The second is a challenge test using the actual process material. Spiking a sample with a known quantity of fine iron and measuring recovery gives a result for the real material and velocity.

The testing approach is described in the magnetic separator testing process .

After installation, monitor the amount of material collected during each cleaning interval. A rising catch can indicate increased wear upstream. A falling catch can indicate poor cleaning or a change in flow conditions.

To specify a separator for a chemical stream, send the material data and operating conditions through the customisation enquiry.

Frequently Asked Questions

Can one separator handle both powder and liquid duty?
Not usually. Powder and liquid duties require different housings, magnetic elements, cleaning methods and pressure ratings. Plants running both normally install separate units.
How often does a chemical-duty separator need cleaning?
The interval depends on the contamination load. Inspect the unit at a fixed interval during the first few weeks, record the catch, and adjust the cleaning schedule from that data.
Does a stronger magnet always remove more iron?
No. Capture also depends on the field gradient, approach velocity and particle size. Reducing velocity can sometimes provide more improvement than increasing field strength.
What documentation should come with a unit?
Field-measurement records, the measurement method and instrument, material certificates for wetted parts, and the pressure-test record should be supplied.
Engineering review

Match the field, housing and cleaning method to the actual stream.

Send the material form, particle size, throughput, temperature, line pressure and target contamination level for a configuration review.

Start your project